Furniture Clinic Wood Stain (Natural Oak) – Fast Drying, Highly Concentrated, and Easy-to-Apply Wood Stain for All Indoor & Outdoor Wood – Water Based & Non-Toxic – 250ml

Product Information

Dark oaks woods tend to have a brown and red-ish hue which can be enhanced and duplicated by our Dark Oak Wood Stain. During extra busy periods, such as in the run up to Christmas, couriers may start doing weekend deliveries but usually deliveries are made during weekdays. A. We recommend leaving the stain to soak into the wood for one or two minutes before wiping the excess off. A foam sponge is highly recommended when working on large flat pieces, as any heavily stained areas can be soaked up by the sponge as you work.

We do have a bigger FAQ sectionwhich you can find a link to from here and at at the bottom of this page. The couriers can leave safe at your door, in a porch, garage, shed or back garden or with a neighbour on your street. Wait four hours for the first coat to dry before applying the second, leave the second coat to dry for four hours.It can be used on all joinery, window frames, doors, door frames, and of course floors, as well as kitchen units, worktops, tables, chairs, furniture, cupboards etc. In the following video we show you how to use our Dark Oak Wood Stain to change the colour of a wooden chair.

Please see below the top 3 questions we get asked that you may find useful to know the answers for right now. However, if you apply too much and it dries too dark, it is much harder to sand, strip and then re-stain the wood! Protect and preserve interior and exterior wood against rot, mould, algae, fungal growth, insect attack and more with these treatments and woodworm killers. Minor runs will normally dry out evenly and should not be noticeable when the wood stain has fully dried. Whatever your age or experience level, you’ll be able to find something to pique your interest at Hobbies.

If you are unsure of what colour you want, start with a light stain and then add more stain until you reach the desired colour.

If the wood is freshly sawn, you may need to start with something more coarse such as 120g sandpaper and work your way up with the Sanding Pads. This is to ensure you measure in the correct way and you are confident that you will be able to install this product at your window. Get them as smooth as possible to have the stain take the same as it does on the other faces of the board. If you don't see the colour you want listed below, you can also mix the different colours of stain together to achieve any colour of Wood Stain you need. Whether you want to darken the natural colour of the wood or create a completely new look, there is an oak stain out there that is perfect for you.Very easy to use, simply apply using a lint-free cloth, brush, or spray, fast to apply, fast to dry. Gel stains tend to take more evenly on soft wood, and make less of a difference on hard woods like oak! There are many different brands and types of stains available, so take your time and find one that you like. After staining wood, you should finish the job by sealing the stain in with one of our Wood Waxes, Wood Varnishes or Wood Oils. New Wood – Needs to be sanded first to create a lovely smooth finish prior to applying the Wood Stain.

If however you have a window that is very high up (the measurement from the top of where the blind will be installed down to the floor is 200cm or more) then you will need a longer than usual chain or cord for you to comfortably reach. Think of it like your skin – if you’ve ever gotten a spray tan (haha), you will know that the fake tan absorbs darker into areas of dry skin – like knees and elbows. I chose it after testing a few other makes and use it on external weather boarding - it gives good water proofing 360 degrees around the house. If the stain still looks splotchy, choose something a bit more opaque with fuller coverage rather than something more transparent.Morrells Water Based Wood Stain is formulated to be 100% chemical or solvent free, using the latest and best micronized water-soluble pigments that create a beautiful color to your woodwork. Shake the bottle thoroughly to make sure pigment dispersal, then add contents to a suitable container and apply using a brush, lint-free cloth or sponge. Please note: After applying Manns Wood Stain and before applying a varnish, oil or wax top-coat, it is essential that the surface of the wood is denibbed or lightly sanded. In all instances, ensure the surface is clean and any saw dust or dirt has been removed before applying the Wood Stain. In accordance with child safety legislation all cords / chains must hang at least 150cm off of the floor.