Gardner Bender DS-130 Duct Seal Compound, 1 lb. Pug, No Size, Grey

Product Information

Selection should be at the design stage, where the seal requirements can be matched to the overall project. Typically, a design specification will require water, gas and perhaps fire resistance together with specific chemical resistance. The life of the seal needed should also be considered. Every seal manufacturer should be able to provide proof of expected life. Over-engineering the seal design should also be avoided. A duct sealing solution that meets the specific needs of the application is the right solution. Roxtec offer a complete sealing solution for use across a huge range of industries both on land and at sea. Their modules are inserted around cables or pipes in frames that are attached to a structure by welding, bolting, casting or core drilled holes for a smart, safe and easy solution.

Following discussions, CSD Duct Seals were brought on board after providing a bespoke solution not only to a technical issue within the green cabinets, but a dramatic cost effective solution to Openreach. Failure to correctly and effectively seal cable ducts can inflict catastrophic damage to LV-HV electrical distribution networks, substations and power supply. View below our complete ranges of Duct Sealing Products including cable transits to provide a watertight seal and defence against flood damage to low, medium and high voltage cable ducts with additional protection against harmful flammable gas migration and fire spread. Energy saving calculations can be carried out after application, but it has been possible to reduce fan speeds and is some cases, reduce fan size after Aeroseal, whilst still achieving the required air volumes.

FiloSeal+ is suitable for sealing several cables or pipes contained in a single duct and allows for re-entry of the seal to add or remove cables or pipes

Approved – ATEX compliantfor hazardous area cable duct sealing in potentially explosive atmospheres, Zone 1 & Zone 2 Aeroseal helps companies meeting the environmental commitments by reducing power consumption and therefore carbon footprint. FiloSeal+ is very easy to apply regardless of the type of cable scenario in the cable ducts as it uses a uniquely shaped foam piece which positions neatly around the cables or pipes in the duct. CSD RISE cable duct seals are specified throughout the electric and water utility networks to provide protection of ducts and duct openings against the dangers of water ingress and gas migration with up to 4 hour fire resistance to the spread of flame where cables penetrate fire rated boundaries and building openings – the watertight, gastight and fire resistant seals provide duct protection with accelerated age tests concluding a 50 year level of protection. duct sealing using csd rise seals

FiloSeal+ is a universal solution for sealing cables and pipes in ducts or bore holes and is suitable for sealing several cables or pipes contained in one duct and also allows re-entry of the seal to add/remove cables or pipes as required. Re-enterable – CSD duct seals enable simple modification for adding, removing or replacing cables in retrofit projectsThe CSDDuct Seal trials were a resounding success, culminating with Openreach rolling this out nationwide within their update of cabinets. In addition CSD Duct Seals are also looking to provide training for all of Openreach installation personnel and are currently working together to provide another project solution.

Duct sealing system FiloSeal+HD is an engineered universal solution for sealing LV-HV cables and pipes in ducts, boreholes or transit frames. The Filoform duct sealing system FiloSeal+HD uses our MD+ sealant which is easily applied from a standard skeleton gun. The high quality, one component, flexible sealant “MD+” is based on a silicon compound that cures with air (Humidity). There are two types of foam I see out and about, a general yellow one for construction plus a fire retardant pink one. Neither one can seal a duct properly Filoform duct sealing systems have been developed to provide an effective gas and watertight seal of underground cable penetrations. When installing our duct sealing system MDII, you will protect valuables from damage which is caused by gas and water leaks. MD5’s resin can be installed in temperatures from 5°C (41°F). In colder temperatures, expansion can be slower but will expand and cure over a more extended time. Expansion time between 8-10 minutes at temperature ranging between 15-20°C. CleaningTrusted – WIMES (Waters Industry Mechanical & Electrical Specification) accepted for duct sealing in the water utility sector FiloSeal+ is suitable for sealing several cables or pipes contained in one duct and also allows re-entry of the seal to add or remove cables or pipes as required. Should any un-mixed material spill onto a surface, a solvent wipe can be used to help clean the area. Reentering & removal

Duct Seals WIMES | The Water Industry Mechanical and Electrical Specifications (WIMES) define the requirements for a wide range of mechanical and electrical equipment used in the UK water industry including cable duct seals. We'll start with some information about polyurethane DIY foam comparing to our MD5 Duct sealing Resin.

The use of expanding foam in construction & mainatenance projects in all industries has increased over time, but it faces major problems when applied wrong, or designed into a project where the foam specs doesnt match the requirements of the project. In this BLOG, we'll cover the reasons why expanding foam fails when sealing cable ducts and what you can do about it.

Power Cables – specified to seal high voltage and heavy armoured power cables in single, trefoil or Triplex arrangement CSD Duct Seals provided extensive trials in the York and Aylesbury area using their simple yet effective product, RISE Duct Seal using a split pvc duct frame to create more space in the existing overpopulated cable ducts within the cabinets. In the UK the DNO’s (Distribution Network Operator) hold a statutory requirement to prevent danger due to the influx of water, or any noxious or explosive liquid, hydrocarbon or gas from the surrounding ground into substations, street boxes and buildings. The electric utility will have an approved method and material to seal ducts in all new, altered or retro-fitted cable installations – this includes the sealing of cable ducts where the ducting enters the switch gear building. FiloSeal+HD is an engineered solution that provides a strong support system using the hexagonal tubes which builds up like a honeycomb structure. FiloSeal+HD is suitable for sealing any cable configuration or pipes contained in one duct and also allows easy re-entry of the seal to add or remove cables or pipes as required In this highly complicated operation, Johnny McQuoid, SFBB programme director for BT Group highlighted the technical challenges of the roll-out. “This is the first large-scale FTTP deployment of its kind in the UK,” he said. “It’s a trial of our planning, building and provisioning processes and we’re learning a lot along the way.”